Author Archives: asharsidd

Scenario#43 – CUCM 9.1(2) RL/RG Reject Issue

Few weeks back I came across a issue for a customer who are on CUCM 9.12() cluster. The issue was outbound calls not reaching either of the MGCP gateways from a Translation pattern even though both gateways were registered fine with Call manager. I checked the E1s and MGCP status and all was OK. TheContinue reading “Scenario#43 – CUCM 9.1(2) RL/RG Reject Issue”

Scenario#42 – CUC not working after adding Secondary Server

I came across an interesting scenario few days back where customer added a CUC Secondary server back to the Cluster but it was not working as it should. Customer had two CUC servers in the cluster in a load-balanced configuration with half of the ports on unity-02(sub) and other half on unity-01(Pub). For some hardwareContinue reading “Scenario#42 – CUC not working after adding Secondary Server”

Scenario#41 – No Ringback tone from H323 Gateway going to SIP trunk

One of our customer reported an issue with ring back tone when calling their Contact center. I made a test call and observed that as a caller when you call their main Contact center number all you hear is dead silence and then when agent picks up the phone you could hear them talk. ThereContinue reading “Scenario#41 – No Ringback tone from H323 Gateway going to SIP trunk”

Scenario#41 – Mailbox in use

A customer reported an issue regarding a user where if she tried to listen to her voicemail messages she would get “Mailbox is in use”. This issue normally happens if any TUI session or VoiceView sessions are open in any other phones having access to that GDM or the ports have become stuck or busy.Continue reading “Scenario#41 – Mailbox in use”

Scenario#41 – UCCX CAD Agent Issue in Call routing

Customer reported a problem about their UCCX version 8.5.1.11001-35 for CAD Agents. This is what they say about the problem: We have a UCCX Agent with a 9951 Cisco Phone with 2 Lines. First line is the private Line Second Line is the agent Line. Agent is logged into CAD with his agent extension. ContactContinue reading “Scenario#41 – UCCX CAD Agent Issue in Call routing”

Scenario#40 – Access Personal Directory/FastDial without PIN

You may have come across this that though you are logged into your profile through Extension mobility but when you try to access your “Personal Directory” you will be prompted for a userid and pin. Unfortunately, this is by design and cannot be changed. There is a workaround to escape entering userid and pin whichContinue reading “Scenario#40 – Access Personal Directory/FastDial without PIN”

Scenario#39 – CIMC of Cisco UCS C210-M2 showing false alarm

I was looking into a case for one of very high profile customer where their CIMC (Cisco Integrated Management Controller) was showing PS Redundancy status as ‘lost’. However, both PSU were up and Normal. Have a look at the screenshot below: By searching through Bug Tool kit I found two bugs for this particular issueContinue reading “Scenario#39 – CIMC of Cisco UCS C210-M2 showing false alarm”

Scenario 38# Call Routing Issue – Intercept Pattern

Had a bizarre issue with one of the customer where they were trying to dial an internal extension and it was going to a mobile phone. There were no CFA/CFNA/CFB set on the extension itself but for some reason it was following this path. The Call manager version was 6.x. The call routing was designedContinue reading “Scenario 38# Call Routing Issue – Intercept Pattern”

Scenario#37 – Phone display “Error Pass Limit”

A customer reported an issue with their 7941 phone. The issue was they plugged in a new 7941 all configured at Call manager and it was showing “Error pass Limit” as follows: This sort of error normally comes when you have one of the following conditions: Too many unassigned directory numbers in Call manager i.e.Continue reading “Scenario#37 – Phone display “Error Pass Limit””